piston ID:
685
Showing 20 Kits in this category (of total 81 kits)
Kit ID: 50
To provide replacement parts and instructions for the installation of rudder pedal and control column boots in aircraft pressurized to the floor. It is recommended that CK184 be installed concurrently with this custom kit if the plugs on the rudder pedals and linkages are worn, damaged and incapable of providing a good seal, or if the plugs are too low or high to properly position boots.
Kit ID: 94
Provides added safety feature of alternate static source for flight instruments for all prop driven Models except 520, 560, 720.
Kit ID: 110
Provides a fuel low level warning system for the earlier Commander Models except 680T, 680V, 680W, 681.
Kit ID: 120
Control of both outflow valves, coupled with new nose cone vent, helps minimize pressurization surges. Outflow valves are controlled to close at a rate that insures smooth initial pressurization of cabin for improved passenger comfort. Models 681, 685, 690.
Kit ID: 123
Modification of nose cowl assembly permitting removal of nose cowl without removing propeller. Improves accessibility for engine maintenance and substantially reduces propeller removal and installation time. Model 685.
Kit ID: 125
Provides a positive stop for the cabin entrance door on long fuselage Twin Commanders giving protection for door hinges and fuselage structure. Models 680FL, 680FL(P), 680T, 680V, 680W, 681, 685, 690.
Kit ID: 144B
Provides replacement of the lower spar cap to restore the structural integrity of the original design of the Models 685, 690, 690A, and 690B.
Kit ID: 151b
Provides an approved recognition light installation to increase the visibility of the airplane during flight for the Models 500S, s/n 3076 and later, 680W, s/n 1726 thru 1850, 681, 685, 690, 690A, and 690B, all serial numbers. Two kits are available--one with a pulsing function and one without.
Kit ID: 159B
Provides approved modifications for nose gear and nose gear support structure problems caused by wear, overload conditions, prior AC-43.13 repairs, etc., for all Models.
Kit ID: 162C
Provides approved kits for repair of the lower fuselage stringers and lower floor keel beam caps for Models 500, 500A, 500B, 500S, 500U, 520, 560A, 560E, 560F, 680, 680E, 680F, 680FL, 680FLP, 680FP, 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, 695 and 720. Kits may be ordered based on extent of damage.
Kit ID: 164
Provides an approved repair for skin wrinkles / buckles located between fuselage stations 234.00 and 239.15 aft of the lower aft corner of the baggage door for Models 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, and 695. This kit adds an external skin doubler in the damaged area.
Kit ID: 175A
Provides an easy-to-install vertical stabilizer lower rib replacement part and an Alternate Means of Compliance for Service Bulletin 218 (AD 95-13-02) for Models 500, 500A, 500B, 500S, 500U, 560, 560A, 560E, 560F, 680, 680E, 680F, 680FL, 680FL(P), 680F(P), 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, 690D, 695, 695A and 720.
Kit ID: 176
Provides an approved replacement for the original-equipment prop de-icer for the Models 685, 690, 690A, and 690B.
Kit ID: 181
Modification designed to repair and replace damage to surrounding skin and attachment structure of the tail tie-down bumper. The modification also improves the attachment of the bumper support to F.S. (429.477 long fuselage) or (355.477 short fuselage) frames. Models 500, 500A, 500B, 500S, 500U, 560, 560A, 560E, 560F, 680, 680E, 680F, 680FL, 680FL(P), 680F(P), 680T, 680V, 680W, 681, 685, 690, 690A, 690B, 690C, 690D, 695, 695A, 695B.
Kit ID: 182J
Provides an approved nose cone mounted landing light installation which increases the visibility of the airplane during landing and have no restrictions regarding when they can be activated during flight. The latest revision includes improved reflector design and replacement ballast. Models 500S, 680W, 681, 685, 690, 690A, 690B.
Kit ID: 184
To provide rudder pedal installation for all serial numbers for Models 680, 680FP, 681, 680T, 685, 690, 690A, 690B, 690C, 695
Kit ID: 189
Repeated removal and reinstallation of the center fuel cell and liner system leads to damage to the parts and oversized assembly holes. This kit provides approved installation of reusable fasteners for assembly of the fuel cell liner system. For Models: 560A/E/F, 680, 680FL/FL(P)/F(P), 680T/V/W, 720, 681, 685, 690, 690A, 690B, 690C, 690D, 695, 695A, 695B
Kit ID: 191
To provide approval and instruction for long seat rails on the left side for passenger convenience. For Models: 680FL, 680T, 680W, 681, 685, 690, 690A, 690B, 690C, and 695.
Kit ID: 204
This kit provides instructions for replacement of 53514-3 and 53534-103 Horns, which are no longer available.
Kit ID: 205
This kit provides instructions for replacement of the 750080-1 & ES10119 spacer, which is a two piece unit.
